Several aspects need to be paid attention to in the installation method of solar led street lights

Several aspects need to be paid attention to in the installation method of solar led street lights The installation method of solar led street lamps is very important. The correct way is to carry out installation and construction according to the installation rules of road lamps. It must be combined with the specific conditions of the installation site to formulate a correct and reasonable installation method for solar street lamps. There will be installation errors. Before installing the solar street light, it is necessary to determine the position of the standing light; survey the geological conditions, if the ground surface is 1m2 soft soil, then the excavation depth should be deepened; at the same time, it must be confirmed that there are no other facilities (such as cables, pipes, etc.) below the excavation position. There is no long-term shading object on the top of the street lamp, otherwise the position should be replaced appropriately. Reserve (excavate) a standard 1.3-meter pit at the position of the vertical lamp; carry out positioning pouring of the pre-embedded parts.

The embedded part is placed in the center of the square pit, one end of the PVC threading pipe is placed in the middle of the embedded part, and the other end is placed in the battery storage place (as shown in the figure above). Pay attention to keep the embedded parts, the foundation and the original ground on the same level (or the top of the screw and the original ground on the same level, depending on the needs of the site), and one side should be parallel to the road; in this way, it can ensure that the light pole is upright and straight Not skewed. Then pour and fix it with C20 concrete. During the pouring process, the vibrating rod should not be stopped to vibrate to ensure the overall compactness and firmness. After the construction is completed, it should be cleaned up in time.

The correct way to install solar street lights: 1. Solar street light installation location The most important thing for solar street lights and solar garden lights is to receive light energy best, so site selection becomes the first consideration in the installation process of solar street lights. At the installation site, first observe whether there are shelters and obstacles around the foundation. There should be no trees, high-rise buildings and other obstacles that can affect the light irradiation, and it is not allowed to install in places with backlight. 2. The basic part of solar street lights.

The size and firmness of the solar street light foundation. Whether the foundation is firm or not directly affects the safety of the light pole, so the foundation must be operated in strict accordance with the construction drawings, and important data such as dimensions and materials must be mastered. The land texture around the base of the solar street light.

This is also closely related to the safety of light poles. The soil around the foundation should have low humidity and high strength to prevent unsafe behaviors such as light poles being tilted by thrust. The position and smoothness of the threading hole of the solar street light foundation.

The function of the threading hole is to lead the battery wire into the light pole from the ground. If the threading hole is offset, the threading hole will be blocked when the light pole is installed. If there is a foreign object or a dead knot in the threading hole, the threading hole will be completely blocked.

Both of these conditions will prevent the battery wire from being brought in, causing the lamp to not receive effective power. 3. The threading part of solar lamps. Solar street lights are absolutely not allowed to have wire joints inside the light pole during the threading process, and all connecting lines must be guaranteed to be a complete line.

(Except for some light sources with their own lead wires, pay attention when connecting the lamp head to the internal light source line of the lamp pole, it must be tightly connected, and do a good job of waterproof and leak-proof. When connecting, pay attention to prevent the lamp head from falling off due to gravity). When threading, you must pay attention to the technique, and it is forbidden to pull hard to prevent the wire from being interrupted by force or the insulation layer is broken to cause leakage.

4. Install LED street light sources and solar panels. The main thing to pay attention to is the firmness of the power cord connection and the tightness of the screws. When all wires are connected, they must prevent falling off and leakage, and the connection is tight and beautiful.

In the process of tightening the screws, you must master the tightness, not too loose or too tight, and use the principle of tightening to move in an appropriate amount. Don't be too tight to prevent the screws from sliding due to excessive force; not too loose to prevent some parts from being shifted due to looseness. When installing the light board, grasp the direction, and the standard time is to face the south direction, because the south direction has the strongest light and the longest sunshine time.

If it is not possible to face the south under special circumstances, the principle is to use the longest lighting time and the largest light intensity. 5. Install solar street light poles. Before installing the solar street light pole, be sure to check all the power lines to see if there is any electrical leakage, and if so, correct it as soon as possible.

Be careful when standing on poles. During the process of tightening the corner screws, adjust the direction of the light pole. Level off, don't lean back and forth.

After all the work is done, the corner screws must be tightened again to keep them secure. Misunderstandings in the installation of solar street lights: 1. Install in places with many shelters. The working principle of solar street lights is that the solar panel absorbs the sun during the day and exists in the battery.

At night, the batteries convert sunlight into electricity to power street lights. At this time, the light will turn on. But then again, solar panels can only store electricity if they absorb sunlight.

If the street lamp is installed in a place with many shelters, such as being blocked by many trees or buildings, it will not absorb sunlight, so the lamp will not be bright or dark. 2. Install near other light sources. Solar street lights have their own control system, which can identify dawn and darkness.

If other power sources are installed next to the solar street light, when the other power sources are on, the solar street light system will think it is daytime and will not light up at this time. 3. The solar panel is installed under other shelters. Solar panels consist of strings of panels.

If one of the strings of panels cannot be exposed to sunlight for a long time, then this set of batteries is equivalent to useless. In the same way, if the solar street light is installed in one place, there will be certain shelters in that place to block a certain area of ​​the solar panel. If this area is not exposed to sunlight for a long time, it cannot convert sunlight into electricity, and the battery in that area is equivalent to a short circuit.

4. Install lamps on both sides of the road, and the solar panels are inclined to face each other. It should be common to install lights on both sides of the road, but there will also be a problem, that is, the sun will only rise from the east. If the street lamp on one side faces east and the street lamp on the other side faces west, one side may be facing away from the sun, so it cannot absorb sunlight because the direction is wrong.

The correct installation method should be that the solar panels face the same direction, and the solar panels on both sides can absorb sunlight. 5. Solar street lights are charged indoors. Solar street lights are installed in sheds or other indoor spaces because of the convenience of lighting.

But if it is installed indoors, the solar street light will not work, because its panels are completely blocked and cannot absorb sunlight, no sunlight can be converted into electricity, and it cannot be illuminated. If you want to install solar street lights indoors, you can install solar panels and lights separately, let the panels charge outdoors, and let the lights illuminate indoors. Of course, if we are lighting indoors, we can also choose other lighting.